Seagate seatools long generic windows#

Go to the Seagate Warranty checker and enter the drive info: Warranty & Replacements | Seagate Support US Also, If you bought it from a third party seller on Amazon, it could have been a return or a refurb. Could be something as simple as a bad SATA cable.

Seagate seatools long generic windows#

The Windows message comes from the SMART info the disk shares with the operating system. The Drive Selection provides some basic instructions and the Rescan Bus push button. The screen consists of three sections, Drive Selection, the device list tree control, and Selected Drive. But, if you do get errors, it shows that it has a much greater chance than normal of a failure. When in Safe Mode the following functions are enabled: Select Device (s) The Select Device (s) toolbar button provides access to the device selection screen.

You may have some other underlying issue. The SMART tests are a warning, not a sure sign that the disk will fail. I cannot find either of these codes online anywhere.

However the Generic Long Test fails with SeaTools Test Code: A1EEE3D2. It includes several tests that will examine the physical media on your Seagate, Maxtor or Samsung disk drive and any non- Seagate disk drive. The Short Drive Self Test fails with SeaTools Test Code: A1EEE3E2. SeaTools for Windowsis a comprehensive, easy-to-use diagnostic tool that helps you quickly determine the condition of the disk drive in your external hard drive, desktop or notebook computer. Direct attached to the motherboard SATA ports, attached to an LSI RAID controller, and even switched formats between 512e/4Kn via SeaChest. Ran Seatools tests on hard drive due to flaky operations that I determined to be hard drive related. I have had them in multiple types of configurations and never had any issues. The older ones end in VE0008, and the new ones end in VE001. I have 8 of the 12 TB Skyhawk AI's-some purchased a few years ago, some a few months ago.

If you look at the release years for the corresponding drive datasheets, you will see they have different timestamps, but the specs are largely the same. My question is can you tell me what does the message. I have Seagate hadd (ST3160023A) and when i tested the HDD with SeaTools the program showed the following message: 'Long Generic test - fail'. The VE002 appears to be older (circa 2020). Hello everyone, i have a little problem with my HDD so i decided to come here and seek some help. connect the hard drive to another working computer, and run Seagate Seatools for Windows (Long Generic test). Boot from disk to run it (will have to disable SecureBoot and enable CSM/Legacy mode). WD 20TB external also on sale for 320 but the Seagate is a much better value /TB and I already have an EXOS drive so Id rather have a matching HDDs later. run Seagate Seatools for DOS (Long Generic test). Any tips Safe to use It's a RAID0 of two drives (I'm not looking for storage/backup recommendations right now, it's not crucial data, thanks). Anyone know if these have an EXOS drive Plan to use it as is and eventually shuck it. See title - Seagate 3TB drive from 2017 passes everything in Seatools, even the Long Generic Test (took 8 hours), but DSM 6 (on DS216j) sees 16 bad sectors ('failing drive'). SeaTools is available for Windows, Linux and DOS.From my research, the ST16000VE002 and ST16000VE000 are the same drive, just different release years. Seagate 16TB External HDD on sale for 229.

Care should be taken only when using the Advanced tools. Most of the diagnostic tests are safe to perform, meaning that there is no loss in data and the tests can also be aborted. The long generic test has the capability to repair bad sectors on external USB hard disks.Īpart form the above tests, SeaTools has a couple of Advanced Tools that allows up-gradation of the drive’s firmware and disk format. Long Generic – This test is extensive and scans the entire drive and may take several hours to complete.Short Generic – This test does a quick scan of the hard drive for possible errors making random read tests.Because of this, the test takes about 4 hours to complete. Long Drive Self Test – This test is more comprehensive than the Short Drive Self Test as it checks each and every sector on the drive.This test is completely data safe and can take 20 to 90 seconds to complete. Short Drive Self Test – In this test the drives run a thorough diagnostic routine that is built in to the hard drive’s firmware.Almost any hard disk health monitoring utility can perform this test. Seagate offers both graphical user interface (GUI) and command line interface (CLI) diagnostic tools for our storage devices. SMART Check – It’s the most basic test where the status of the hard disk is determined from the S.M.A.R.T monitoring feature built in on the disk.